Short answer: a Dynamic infrared sauna has a handful of replaceable electrical parts: the power supply (the control box on the roof), the control panels, the heat emitters, the temperature sensor and the lights. Before you order one, check the connections and the reset button, because many faults turn out to be a loose plug. If a part does need replacing, have your model number (it starts with DYN-), your serial number and a photo of the part's label ready, and contact us.
The main parts of a Dynamic sauna
This table is based on the parts and troubleshooting sections of Dynamic's owner's manuals. Layouts vary a little by model, so check the manual for yours on our Dynamic owner's manuals page.
| Part | Where it is | What it does | Signs it may need replacing |
|---|---|---|---|
| Power supply (control box) | On top of the roof panel | The control center. The power cord, heater cords (HT1 to HT6), lighting, roof lamp and control panel all plug into it, and it has a fuse reset button | No power at the panel after a reset, a damaged power cord, or signs such as a burning smell, unusual heat or strange sounds |
| Control panel | Beside the door, inside and on many models outside too | Sets temperature, time, lights and audio | Won't turn off, lights don't come on or buttons don't respond after you reseat its connection. A hum from the speakers on Bluetooth that stops when you use the AUX cable also points to the panel |
| Heat emitters | Walls, under the bench and on the floor | Carbon or ceramic panels that produce the infrared heat | One panel stays cold after you've checked its cord at the panel and on the roof |
| Temperature sensor | The black probe in the ceiling above the bench | Tells the control panel the cabin temperature | The panel shows "-L" or the emitters won't heat. Some saunas ship with a spare sensor |
| Lights | Ceiling (chromotherapy) and, on some models, reading or roof lamps | Interior and accent lighting | A light still doesn't work after you reseat its connection on the roof |
Bench and floor emitters run at lower wattage than the wall panels, so they are meant to feel only warm, not hot. Bluetooth and speaker problems have their own guide: how to connect and fix Dynamic sauna Bluetooth.
Check these before you order a part
- Unplug the sauna first, or switch the breaker off if it is hard-wired. Work with dry hands.
- Reseat the connections on the roof: the heater cords, the "PANEL CONTROL" or "CTRL" harness and the "TEMP SENSOR" wires. Make each one snug.
- Press RESET on the power supply. It's on the same side as the power cord.
- Check the outlet and breaker. The manuals say not to use a GFCI outlet, an extension cord, an adapter or a surge protector, because a GFCI can start tripping even after months of normal use.
- Reseat the control panel plug. Unscrew the wood frame around the panel, lift the panel out and reconnect the black plug on its back.
If that doesn't fix it, our Dynamic sauna troubleshooting guide walks through each symptom in more detail.
Part codes we can source
These are power supply and control panel codes we can request for Dynamic owners. Always match the code on the label of the part you're replacing, because a part with a different code may not fit or work with your sauna.
Power supplies
- D9101AC, G9272AC, D9235AC, D6444AC, G6445AC
- G9272+CL, D9235+CL, D6444+CL, G6445+CL
- D9235+CL BT, D6444+CL BT
- 3.0 15AMP, 3.0 20AMP
- MX-15-BT, MX-15-MP3, MX-15-RD, MX-20-BT, MX-20-RD
Control panels
- DYN-CP-Red-SL, DYN-CP-Red-DL
- DYN-CP-Green-SL, DYN-CP-Green-DL
- DYN-CP-Blue-DL
- MX-CP-Red, MX-CP-Green-BT
Need something that isn't listed, such as an emitter, a sensor or a light? Ask us anyway.
How to order a replacement part
- Find your model number. It starts with DYN- and is on your order confirmation and product page.
- Find your serial number. The manuals say it's on the sauna's front panel, rear panel or shipping carton.
- Photograph the label on the part you're replacing, plus the problem if you can (for example, the "-L" on the display).
- Send us all three through our contact page. We'll confirm the right part and let you know when it can ship.
The manuals say replacement parts must meet the manufacturer's specifications, because an unapproved substitute can cause a fire or an electric shock. After any repair, ask the technician to do a safety check before you use the sauna again.
Is the part covered by warranty?
According to Dynamic's owner's manuals:
- 5 years on heating elements and electronics, from the date of purchase.
- 1 year on the wood structure and the radio.
- Parts only: the warranty covers parts, not labor.
- Indoor use only: placing the sauna outdoors voids the warranty, as do modifications and repairs that the manufacturer hasn't authorized.
- Register it: mail the warranty card with proof of purchase within 60 days. The warranty covers the original buyer at the original site and isn't transferable.
- Returns of faulty parts: a part claimed under warranty may need to be sent back, and the owner pays that shipping.
Terms can differ between model years, so check the warranty page in your own manual.
How to make the parts last
- Unplug the sauna before cleaning, and wipe the wood with plain water and a soft, damp cloth. Our sauna cleaning guide has a full routine.
- Never pour water or other liquids on the heat emitters, and don't bump or hit them.
- Don't switch the power on and off over and over, which the manuals say shortens the life of the electronics.
- Keep the power cord where it won't be walked on or pinched, and don't store anything on top of the sauna.
- Check that everything works before each session, and stop using the sauna if something seems wrong.
Still building yours? Follow our Dynamic sauna assembly guide so every connection is made right the first time, or browse the current range of Dynamic infrared saunas.




